SHEAR STRENGTH OF ONE-WAY RIBBED SLABS WITH STEEL FIBER CONCRETE
DOI:
https://doi.org/10.56238/arev8n3-166Keywords:
Ribbed Slab, One-Way Slab, Shear, Steel FiberAbstract
The ribbed slabs are used both in small and large constructions, and its use is growing due to the advantages that this constructive system provides. However, considering the demeanor of these slabs without transverse reinforcements (stirrups), few studies were made in Brazil. This study brings an experimental analysis of 8 unidirectional ribbed slabs of reinforced concrete subjected to loads perpendicularly distributed to the ribs. 4 (four) reference slabs and 4 (four) reinforced slabs with steel fibers with a length of 1,700 mm and width ranging from 650 to 950 mm were tested, all with table thickness of 40 mm and ribs with cross section of (100 x 100) mm². The compressive strength of concrete was approximately of 30 MPa. The results were compared to those estimated by the design codes ACI 318 [1], EHE 08 [2], NBR 6118 [3] and MC10 [4]. It was verified that the increase in shear and bending strength of the reinforced slabs with fibers was substantial, what makes those slabs technically feasible.
Downloads
References
[1] ACI 318. Building Code Requirements for Structural Concrete, American Concrete Institute, Farmington Hills, Michigan, 2014.
[2] INSTRUCCION ESPAÑHOLA DE HORMIGÓN ESTRUCTURAL (EHE 08) – Norma españhola sobre el cálcuo y seguridade en estructuras de hormigón– Madri, 2010.
[3] ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS (ABNT). NBR 6118 – Projeto de Estruturas de Concreto. Rio de Janeiro, 2023.
[4] CEB-FIP MODEL CODE 2010: Final Draft. Model Code prepared by Special Activity Group 5, Lausanne, September 2011. (This final draft has not been published), 2010.
[5] BOCHI JÚNIOR, C.F. Lajes Nervuradas de Concreto Armado: Projeto e Execução. Dissertação (Mestrado) – Escola de Engenharia de São Carlos, Universidade de São Paulo, São Carlos. 1995.
[6] BARROS, J., RIBEIRO, A., CUNHA, V., ANTUNES, Steel fibres for the shear resistance of reinforced concrete beams. Dimensionamento de estruturas de betão reforçado com fibras de aço, DEC – UM, Portugal, 2003.
[7] G. P. GAVA et al. Ensaio de flexão de vigas com concreto reforçado com fibras de aço: influência na presença e posicionamento do entalhe e do número de fibras na seção fissurada- e. Mat, vol 1, n. 2, p. 114-127, Novembro 2004.
[8] CLAUDIO ALCIDES JACOSKI et al. Prospecção tecnológica de concreto com adição de fibras - Cad. Prospec, Salvador, v. 7, n. 3, p. 368-376, jul./set. 2014.
[9] RÜSCH, H. Researches Toward a General Flexural Theory for Structural Concrete. ACI Journal, p. 1-28. July 1960.
[10] ROMBACH, G.; LATTE, S. Shear Resistance of Bridge Decks without Shear Reinforment. Proceeding of the FIB Symposium “Tailor Made Concrete Structures”, Amsterdam, 2008.
[11] MACGREGOR, J. G. Reinforced Concrete: Mechanics and Design. New Jersey, Prentice-Hall; Third Edition, 197p.; 1997.
[12] COLLINS, M.P.; BENTZ, E.C; SHERWOOD, E.G. Where is Shear Reinforcement Required? Review of Research Resultsand Design Procedures. ACI Structural Journal/September- October, 2008.
[13] ACI-ASCE Committee 426. The Shear Strength of Reinforced Concrete Members. In: Journal of the Structural Division, Vol. 99, N° ST6, June, 1973, pp. 1091 – 1187.
[14] GARCEZ, E. O. Análise teórico-experimental do comportamento de concreto reforçado com fibras de aço submetidos a cargas de impacto. Dissertação de Mestrado apresentada ao Programa de Pós-Graduação em Engenharia Civil da Universidade Federal do Rio Grande do Sul. Porto Alegre, 2005.
[15] HAZRINA, A. MOHD, H. MOHD, H. AFIDAH, A. B. SITI, H. H. AND FADHILLAH, A. R. Flexural Strength and Behaviour of SFRSCC Ribbed Slab Under Four Point Bending. Proceedings of the 3rd International Conference on Construction and Building Engineering (ICONBUILD), Indonesia, August/2017.
[16] ARSLAN, G. Shear Strength of Steel Fiber Reinforced Concrete (SFRC) Slender Beams. KSCE Journal of Civil Engineering, structural, No. 18 (2), p 587-594, 2014.
[17] MACGREGOR, J.G.; WIGHT, J.K. Reinforced concrete – Mechanics and design. 4a ed., Upper Saddle River, Ed. Prentice Hall, 1132p. 2012.
[18] YOON-KEUN KWAK, MARC O, EBERTHARD, WOO-SUK KIM, AND JUBUM KIM. Shear Strength of Steel Fiber-Reinforced Concrete Beams without Stirrup. ACI Structural Journal, No 5. August, 2002.
[19] DINH, H. H., PARRA-MONTESINOS, J., WIGHT, J. K. Shear Behavior of Steel Fiber Reinforced Concrete Beams without Stirrup Reinforcement. ACI Structural Journal, V. 107, No 5. September, 2010.
[20] LIM, D. H., OH, B. H. Experimental and theoretical investigation on the shear of steel fibre reinforced concrete beams. Engineering Structures, Elsevier. No 21, p 937-944, 1999.
[21] ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS (ABNT). NBR 15530. Fibras de aço para concreto – Especificações. ABNT - Associação Brasileira de Normas Técnicas. Rio de Janeiro, 2007.
[22] ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS (ABNT). NBR 5739 – Ensaio de compressão de corpos de prova cilíndricos de concreto. Rio de Janeiro, 2007.
[23] ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS (ABNT). NBR 7222 – Argamassa e Concreto – Determinação da resistência à tração por compressão diametral de corpos de prova cilíndricos – Método de Ensaio. Rio de Janeiro, 2011.
[24] ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS (ABNT). NBR 8522 – Concreto – Determinação do módulo de deformação estática e diagrama tensão-deformação – Método de Ensaio. Rio de Janeiro, 2008.
[25] MORAES NETO, B. N. BARROS, J. A. O.; MELO, G. S. S. A. A model for the prediction of the punching resistance of steel fiber reinforced concrete slabs centrically loaded. Construction and Building Materials, 46, pp. 211-223, 2013.
[26] SOUZA, W. M. CAETANO T. R. G. FERREIRA M. P. OLIVEIRA D. R. C. Resistência ao cisalhamento de lajes nervuradas unidirecionais de concreto armado. Instituto Brasileiro do Concreto (IBRACON) Revista, Volume 7, Número 4, p. 648-684 • ISSN 1983-4195, Agosto, 2014.
